Defcon Kaklkaklkekl (Wiki)

**This is an old revision of the document!** ----

====== Using Nortel Unistim phoneswith FreePBX/Asterisk/AsteriskNOW ====== ===== Install the chan_unistim driver ===== <code> yum update yum install asterisk14-devel wget http://mlkj.net/UNISTIM/chan_unistim-1.0.0.5f.tar.bz2 tar zxvf chan_unistim-1.0.0.5f.tar.bz2 cd chan_unistim-1.0.0.5f make make install </code> ===== Set up config entries for Unistim ===== Edit /etc/asterisk/unistim.conf Note that we are using the planned extension number as both Unistim ID and Unistim Line number, in this example, 6007. <code> [6007] ; name of the device, preferably the same as the extension number device=000ae40a6c38 ; mac address of the phone country=no ; country (ccTLD) for dial tone frequency. See README, default = us extension=line ; To register for extension. This is needed IN ADDITION to a dialplan entry context=from-internal ; freePBX uses this for internally originated calls. callerid="Desk" <6007> ; Set a sane CID-display titledefault="Ext # 6007" ; default = "TimeZone (your time zone)". 12 characters max timeformat=2 ; 0 = 0:00am ; 1 (default) = 0h00, 2 = 0:00 line=>6007 ; Device and extension number. Only one line by device is currently supported. ; Beware ! only bookmark and softkey entries are allowed after line=> bookmark=2@Logout@8001** ; I use the keys above the Line key for logging in and out bookmark=1@Login@8001* ; of my primary Queue... </code> ===== Add an extension / dialplan entry ===== In freePBX, go to Admin / Extensions, and Add Extension (With the previous example as a base, Caller ID name is "Desk", and Unistim number is 6007) * Select device: Other (Custom) device * Set the display name to the same as the String part of the callerid in unistim.conf * Desk * Set the dial string to "USTM/ustmline@ustmname" * UTSM/6007@6007 * Submit Reload your asterisk config with the "Reload bar" in freepbx. ===== Restart your Asterisk server ===== You *could* load the module from the asterisk prompt, but to be absolutely shure, restart the setup. Either run "restart now" on an *-prompt, or do it from a shell-prompt: <code> asterisk -rx "restart now" </code> ===== Set up your Nortel phone ===== From voip-info.org, I have stolen this, as it works ;) * Power on the phone * Wait for message "Nortel Networks" * While the "Nortel Networks" splash is showing, quickly press each the four softkeys just below the LCD screen, in sequence from left to right. (you can do it real easily with your four fingers as if on a piano - one-two-three-four). This is known as 'swiping' a phone. * If you see "Locating server", you weren't fast enough. Power off (or reboot the phone - see below) and try again <code> - EAP Enable? (0-N,1-Y):0 - DHCP? (0-N,1-Y):1 - Cached IP? (0-N,1-Y):1 - DHCP:0-Full,1-Partial:1 - S1 IP: xxx.xxx.xxx.xxx (Asterisk's Server IP Address) - S1 PORT: 5000 - S1 ACTION: 1 - S1 RETRY COUNT: 10 - S2 IP: xxx.xxx.xxx.xxx (Asterisk's Server IP Address) - S2 PORT: 5000 - S2 ACTION: 1 - S2 RETRY COUNT: 10 - Cfg XAS? (0-No,1-Yes):0 - VOICE VLAN? (0-N,1-Y):0 - PC PORT? (0-OFF,1-ON):1 - DATA VLAN? (0-N,1-Y):0 - DUPLEX (0-AUTO,1-FULL):1 - SPEED (0-10Mb,1-100Mb):1 - GARP Ignore? (0-N,1-Y):1 </code>